Profile: BlueFire Admin

Send the App’s event log (Settings/Send the Event Log) and I’ll take a look. Let me know when you have sent the event log too.

Try clearing Persistent Data (App Settings page). See the Getting Started document's Persistent Data section for more information.

12.4.0 Updates: 4/13/2026

     Highlights:

        Range alerts (Warning and Danger) can now be set to delay a number of seconds before showing the alert. Use the Audio Alerts options 'Delay Time' to set the number of seconds.
        
        Range alerts can also be set to not show the alert if the engine is idling. Use the Audio Alerts option 'Idle RPM' to set the maximum RPM for engine idle and the Audio Alerts option 'Ignore Idle' to not show the alert.  
  
     Updates:
    
     •  Adapter Connection
        1. Fixed App hanging after disconnecting from the Adapter.
        2. Fixed an unregistered Adapter causing a reconnection attempt.
        3. Fixed the App attempting to reconnect when the user is connecting to the Adapter.

     •  Home Page
        1. Fixed Android and iOS not showing messages (at the bottom of the page).
    
     •  Audio Alerts Page
        1. Added 'Ignore Idle', 'Idle RPM' and 'Delay Time' options.
    
     •  Customize Dash Page
        1. Fixed Audio Alerts options not defaulting to App Audio Alerts.
    
     •  Customize Gauges Page
        1. Fixed Audio Alerts options not defaulting to Dash Audio Alerts.
    
     •  Logging Page
        1. Fixed not editing for an invalid File Name thus causing a system error.
    
     •  Settings Page
        1. Fixed 'Reset Adapter' causing the Adapter to reconnect.

     •  Other
        1. Internal updates and improvements.
    
     •  Getting Started Document
        1. Updated to version 12.6.0.

Search the web, or join SAE.

4.2.0 Updates: 3/1/2026

        •  Better memory management with substantially less risk of memory corruptions.
        •  A user factory reset cycle is now performed only after a power cycle.
        •  The Adapter will go to sleep right after the user factory reset cycle.
        •  When not connected, the Adapter will reboot every two hours.
        •  When the App disconnects from the Adapter, the Adapter will reboot. If the Adapter is set to sleep it will immediately go to sleep.
        •  When the Adapter reboots, the LEDs will blink cyan for 8 seconds if not sleeping, otherwise (sleeping) the LEDs will blink a dim cyan quickly.
        •  Power cycling is fine during a reboot but App connection will wait.
        •  Adapter firmware updates are now no cost with free USPS ground shipping.

4.2.1 Updates: 3/8/2026

        •  Fixed Adapter locking up when first plugged in (requires re-plugging in).
        •  Saving Device Name and MAC Address in case it cannot be retrieved.
        •  Reduced LED brightness in half for cyan, yellow, and magenta LEDs.
        •  Updated the Firmware Update program to version 12.2.0.

4.2.2 Updates: 3/10/2026

        •  Reduces the likelihood of raising a J1708 ECM J1587 fault (eg. "No J1587 DATA") when plugging in the Adapter.

4.2.3 Updates: 3/24/2026

        •  Fixed J1708 not setting the App's Key On (solid blue Led) when connecting with the ignition key on.

In order to add these yourself you would need the PGN, SPN position and length, the resolution and a way to convert the data. However if you know this information, you can use the Settings/System/Advanced Functions to query the data.

The data can get hardcoded into gauges when there is enough support for them.

Good idea. Will look into it.

The latest App version (12.3.1) has Crankcase Pressure in the Logging page.

Eric Necker wrote:

Have you taken a look at the Getting Started document's Fuel and DEF section? You may need to have the App calculate fuel level for you.